Analog Transmission Systems  (753)

High bandwidth, up to 270Mbs, 10/100 Ethernet, MDI/ MDIX and IEEE802.3/ 802.3x/ 802.3u/ 802.1d,/ 802.1p/ MOCA.

ComNet FVT/FVR1001(M)(S)1 is a video transmitter and receiver that supports the transmission of short-haul quality 10-bit Digitally Encoded video over one multimode or single mode optical fiber. It is universally compatible with major CCTV camera manufacturers. It has a plug-and-play design that ensures ease of installation and no electrical or optical adjustments are ever required. It has a bi-colour (Red/Green) LED indicators that are provided for rapidly ascertaining equipment operating status. It is interchangeable between stand-alone or card mount configurations.

The ComNet CWFE1COA XPOE /M supports 100Mbps Ethernet transmission as well as Power over Ethernet (PoE)at data rates of 100Mbps, and transmission distances of up to 305 meters (1000 feet).

Designed to be completely transparent to all camera and monitor manufacturers. 2% Differential gain with 2 degree differential phase.

RS232 Tranceiver Data System transmits and receives RS232 data on dual multimode optical fiber. Designed for continuous long range interference free data transmission. Diagnostic indicators provide a quick visual indication of system status. Data rate of up to 19.2Kbps with a 5 pin screw terminal Data connector. Has a wavelength of 850nm.

RS422 Tranceiver Data System transmits and receives RS422 data on dual multimode optical fiber. Designed for continuous long range interference free data transmission. Diagnostic indicators provide a quick visual indication of system status. Data rate of up to 19.2Kbps with a 5 pin screw terminal Data connector. Has a wavelength of 850nm.

Preferably unshielded twisted-pair cables should beused for the signal transmission.

2.4 GHz & 5 GHz radio band support., Compliant with 802.11a/b/g/n, Wi-Fi Protected Setup and 1 WAN/ 4 LANs 10/100 Ethernet ports.

2.4GHz & 5GHz radio band support, Compliant with 802.11a/b/g/n, 1 LAN 10/100 Ethernet port and AP / Reapter / AP Client mode.

Compliant with ITU G.954, Physical interface with F-connector and Power on Ethernet support.

High bandwidth, up to 200Mbs, PLC, 10/100 Ethernet, Compliant with IEEE802.3/802.3u, HomePlug AV, HomePlug 1.0.

ComNet FVT20 is a dual video transmitter that supports two independent AM video signals in one module on two independent multimode fiber optic cables. The module is not a multiplexer. It is ideal for CCTV installations and can be used to double the fixed video capacity of the C1 rack for up to 28 independent video channels per card cage. It is compatible with the FVR11M, FVR10M, FVR21, and FVR22 receivers. It has a plug-and-play design that ensures ease of installation requiring no electrical or optical adjustments. The transmitter incorporates a bi-colour (Red/Green) indicating LED for monitoring proper system operation. It is interchangeable between stand-alone or card mount configurations.

ComNet FVR22/LV is a dual video receiver that consists of two independent AM video fiber optic receivers in one module. It uses two independent multimode fiber optic cables to receive two separate signals from two transmitters. The module is not a multiplexer. It incorporates a “Loss of Video” relay for each channel. Upon loss of video signal or optical fiber break, the normally closed relay opens. It is ideal for CCTV installations and the rack mount version can be used to double the fixed video capacity of the C1 rack for up to 28 independent video channels per card cage. It utilise Automatic Gain Control (AGC). The receiver is compatible with the ComNet FVT11M and the FVT20 dual video transmitter. It has a plug-and-play design that ensures ease of installation. Its bi-colour (Red/Green) LED indicators are provided for rapidly ascertaining equipment operating status.

ComNet FVT11MAC single mini video transmitter supports transmission of a fixed video signal using AM modulation on one multimode fibre optic cable. It is compatible with the FVR11M, FVR10M, FVR21, and FVR22 receivers. Plug-and-play design ensures ease of installation requiring no electrical or optical adjustments. The transmitter incorporates a bi-color (Red/Green) indicating LED for monitoring proper system operation.

Remote Video Transmission via Fixed and Cellular Phone Networks ISDN - GSM/HSCSD - GPRS and DX version for external modems.

The ComNet FDC8 Series contact closure transmitter and receiver provides transmission of up to eight independent contact closures over one RS232 link or optical fiber. Microprocessor-based logic sends the contact information in packets that are ordered and encoded, ensuring extremely robust transmission.

UTP / CAT 5 transmission, 32 channels, TX, Telemetry Control, 1067 ~ 2438, PAL / NTSC, 70, 2,540, 42 x 430 x 203, 24 V AC , -10 ~ +50, 0 ~ 95

UTP / CAT 5 transmission, 1 channels, Telemetry Control, 228, PAL / NTSC, 10, 60, 18, 15 x 16 x 47, -10 ~ +70, 0 ~ 95

ComNet FVR11M is a mini video receiver that detects an AM video signal on one multimode fiber optic cable. It utilises Automatic Gain Control (AGC) and is compatible with the ComNet FVT11M and the FVT20 transmitters. It has a plug-and-play design that ensures ease of installation requiring no electrical or optical adjustments. Its bi-colour (Red/Green) LED indicators are provided for rapidly ascertaining equipment operating status. It is only available in stand-alone configurations.

UTP / CAT 5 transmission, 8 channels, TX, 610 ~ 1219, PAL / NTSC, 6, 70, 2,040, 42 x 430 x 203, 80 ~ 240 V AC, -10 ~ +50, 0 ~ 95

ComNet FVT10 single channel video transmitter supports one independent AM video signal on one independent multimode optical fibre. It is compatible with the FVR10, FVR10M, FVR11, FVR11M, FVR21 and FVR22 receivers. Plug-and-play design ensures ease of installation requiringno electrical or optical adjustments. The unit may be either wall or rack-mounted, or may be DIN-rail mounted.

ComNet FVT1M1/M s a video transmitters that transmit one channel of video over one optical fiber. It is available in multimode and single-mode versions. It is compatible with the FVR10C1(M,S)1, FVR20C2(M,S)2 and FVR40C4(M,S)4 series of receivers. It has a plug-and-play design that ensures ease of installation requiring no electrical or optical adjustments. Its bi-colour (Red/Green) LED indicators are provided for rapidly ascertaining equipment operating status. It is ideal for mounting where space is limited or can be mounted inside equipment housing.

Vigitron expands its MaxiiCopper family with the introduction of the 8 and 16 ports high-speed Ethernet extender hubs. Models Vi2408 and Vi2416 are the industry's first high-density and rack mountable long distance Ethernet solutions that provide an easy transition from analogue to digital CCTV systems using the existing coax infrastructures. When deployed along with the MaxiiCopper Vi2401 Ethernet Extender at the remote end and the Vi2408 or Vi2416 hub at a central location, they establish a full-duplex, full-rate Ethernet connection up to 5,500 feet (1,680 m) at 10Base-T or 2,100 feet (640 m) at 100Base-T. They are completely transparent to the IT networks and do not need any IP programming. These extenders are excellent for high network bandwidth requirements of mega-pixel cameras or multiple IP cameras. Their high data rate balances the best possible network throughput and long-reach distance design. Vigitron MaxiiCopper series consist of comprehensive solutions over coax cable as well as the groundbreaking Ethernet Extension over UTP cable. These products provide simple and cost-effective upgrade path for a wide range of security and IT applications. Vigitron is a leading manufacturer of innovative transmission solutions for the global security and IT market. Our products enable you to use your copper infrastructure for either analogue or IP CCTV systems at extended distances. We are committed to employing state-of-the-art technology to offer the best products at exceptional value, accompanied by excellent customer service. We bring you the future now. For additional information on the advantages of Vigitron products, contact us at +1 888-574-8942, e-mail [email protected], or visit http://www.vigitron.com.

Proxim Wireless' GX800 supports an array of user configurable channel bandwidths from 7-56MHz. Join the free Webcast to learn more.Tsunami™ GX800 is a high speed Point-to-Point (PtP) licensed microwave product capable of operating in 6–38* GHz licensed bands with more than 600Mbps aggregate throughout capacity, supporting an array of user configurable channel bandwidths from 7-56MHz. The product has an extremely small foot print and comes in a spli-mount design constituting of a compact indoor unit (IDU) and outdoor unit (ODU) that are a snap to install.The Tsunami GX800 Series is an outcome of Proxim’s extensive RF technical expertise and years of broadband wireless access products experience. The GX800 Licensed Point-to-Point products are technically advanced, highly reliable and very cost effective.The Tsunami GX800 uses highly advanced radio technology. The product is designed for PDH,SDH and Wireless Broadband applications, utilizing modulation schemes from QPSK to 256QAM and high data rates. The product supports High Transmit Power Levels with up to +27dBm for certain frequency bands. The product is optimized for high speed Ethernet networking and for transmission of standard E1 or E3 channels.Tsunami GX800 is not just another typical PDH/SDH platform. It houses a unique innovative proprietary packet system with different priority for each transmission channel. This advanced prioritization platform intelligently allocates transmission capacity depending on modulation scheme and channel bandwidth controlling adaptive selection of user interfaces and their speeds.Advantages and key features6-38* GHz Frequency band supportWide band support from 7-56MHz RF Channel BandwidthsSupports QPSK/16QAM/32QAM/64QAM/128QAM/256QAM Modulation schemesHigh Tx Power radioLow noise figure, low phase noise and high linearityCompact and lightweight design, the smallest IDU in its classVery high frequency stability +/- 5 ppmWide operating temperature range for ODU: -40 to +65°CUp to 16xE1 or 1xE3, one Gigabit Ethernet and one Fast Ethernet traffic interfaces with truen traffic capacity from5Mbps up to 622Mbps.Capacity is dynamically allocated between E1/E3 channels and EthernetFeatures ATPC and Adaptive Modulation (user defined) Built-in Spectrum Analyzer, BER Tester, and Throughput, WAN Utilization chartsODU features standard direct ‘slip fit’ mountingFully supported by Proxim Vision ES Network Management Solution*Designed to meet FCC, ETSI and CE safety and emission standardsSupports popular ITU-R standards and frequency recommendations

UTP / CAT 5 transmission, 8 channels, TX, 610 ~ 1219, PAL / NTSC, 10, 6,650, 430 x 42 x 305, 110 ~ 220 V AC, -10 ~ +50, 0 ~ 95

ComNet FVT/FVR8SFP2R optical video link provides eight 10-bit medium-haul quality digital video channels, eight bi-directional data channels and has dual optical (SFP) ports to provide a redundant Point-to-Point topology. The redundant Point-to-Point topology using the dual optical ports provide fail safe operation in the event of loss of one fiber or one optical module. Each port accepts a wide variety of SFP modules.

1 channels, 1, 500, 70 x 80 x 140, 20mA, 230 V AC, -25 ~ +40, IP67

Fibre Optic transmission, 8 channels, TX/RX, 8, 1, Digital, PAL, NTSC, 900, 128 x 71 x 190, < 12 W, 11 ~ 16 V DC, -40 ~ +74, 0 ~ 95, 1 Vpp, 75 Ohm

The LTC 4628 and LTC 4629 are a bidirectional transmission system designed to implement a complete CCTV system using a single optical fiber cable.  This system independently transmits a video signal from the camera location to the controller location, while simultaneously transmitting Allegiant Bi-Phase control code from the controller location to the camera location.  The video channel is compatible with monochrome or color cameras.  The data channel is compatible with control systems that utilize simplex RS-232 or RS-422 signals. Both units incorporate LED indicators to provide quick visual indication of the module performance.  The LTC 4629 Transceiver Series is also compatible with the ENV Series of Bosch AutoDome® Cameras that incorporate an integral fiber optic transceiver.

ComNet FVT/FVR80D4SFP optical video link provides transmission of eight 10-bit short-haul quality digital video channels and four bi-directional data channels through a selectable small form factor pluggable module (SFP). The data channels support RS232, RS422 and 2 wire and 4 wire RS485. Plug-and-play design ensures ease of installation and no electrical or optical adjustments are ever required. Bi-colour (Red/Green) LED indicators are provided for confirming operating status. The unit is interchangeable between stand-alone or card mount configurations.

Fibre Optic transmission, 4 channels, TX/RX, 4, 1, Digital, PAL, NTSC, 490, 128 x 35 x 190, < 6 W, 11 ~ 16 V DC, -40 ~ +74, 0 ~ 95, 1 Vpp, 75 Ohm

UTP / CAT 5 transmission, 4 channels, TX, 610 ~ 1219, PAL / NTSC, 10, 198, 126 x 171, 110 ~ 220 V AC, -10 ~ +50, 0 ~ 95

UTP / CAT 5 transmission, 1 channels, Telemetry Control, 228, PAL / NTSC, 10, 60, 18 , 14 x 24 x 32, -10 ~ +70, 0 ~ 95

ComNet FVR21 dual video receiver detects two independent AM video signals in one module on two independent multimode fibre optic cables. The modules utilises Manual Gain Control. The receiver is compatible with the ComNet™ FVT11M and the FVT20 dual video transmitter. Plug-and-play design ensures ease of installation. Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment operating status.

ComNet FVT/FVR40SFP optical video link provides four 10-bit medium-haul quality digital video channels, using optical small form factor pluggable modules (SFP). Plug-and-play design ensures ease of installation and no electrical or optical adjustments are ever required. Bi-colour (Red/Green) LED indicators are provided for confirming operating status. This unit is interchangeable between stand-alone or card mount configurations.

ComNet FVT/FVR80D8SFP optical video link provides transmission of eight 10-bit short-haul quality digital video channels and eight bi-directional data channels through a selectable small form factor pluggable module (SFP). The data channels support RS232, RS422 and 2 wire and 4 wire RS485. Plug-and-play design ensures ease of installation and no electrical or optical adjustments are ever required. Bi-colour (Red/Green) LED indicators are provided for confirming operating status. The unit is interchangeable between stand-alone or card mount configurations.

Alvarion BreezeMAX PRO is an CPE developed to use the new Intel PRO/Wireless 5116 broadband interface WiMAX chip and WiFi interface. BreezeMAX is Alvarion's WiMAX platform that uses OFDM technology for advanced Non-Line-of-Sight (NLOS) functionality and is designed for operators to offer broadband IP-based data and voice services. Its carrier-class design supports broadband speeds and quality of service (QoS) for voice and multimedia applications enabling operators to offer multiple services to thousands of subscribers with a single base station. The BreezeMAX Pro has been built to the specifications of IEEE 802.16-2004 for seamless integration into existing BreezeMAX networks. Radio access method: TDMA FDD. Central frequency resolution: 125KHz. Data Communication: IEEE 802.3 CSMA/CD. Air interface Communication: IEEE 802.16-2004. VLAN support: IEEE 802.1Q. Traffic classification: Layer 2 IEEE 802.1p, IP DiffServ Code Points DCSP.

The LTC 4641 Series Transmitters and LTC 4642 Series Receivers are designed for transmission of CCTV video signals.  Efficient installation is assured because there are no user adjustments required.  The wide bandwidth transmission capability of these units enables clear, sharp black and white or color pictures to be transmitted over long distances.  The compact transmitters are small enough to be connected directly to a camera’s BNC connector, thereby simplifying installation.

The ComNet™ FVT10C1(M,S)1/M series video transmitters transmit one channel of video plus one contact closure over one optical fiber. The FVT10C1M transmitter is available in multimode and single-mode versions. This FVT10C1M is compatible with the FVR20C2(M,S)2 series dual channel receivers.

The NEW BreezeMAX Extreme all-outdoor 802.16e WiMAX base station simplifies your network architecture and maximizes your ROI with its compact, all-in-one design. Integrated base station, antenna, ASN Gateway and GPS receiver enable "zero-footprint" deployment while offering a lower total cost of ownership. Locate your BreezeMAX Extreme on communication towers, rooftops and street poles.Advanced features include MIMO, HARQ and QoS for superior capacity, range and performance.Choose 3.65, 4.9, 5.3, 5.4 or 5.8 GHz to quickly and easily expand your network and increase subscribers.Learn more in the BreezeMAX Extreme Information Kit, packed with detailed features, benefits and advantages for you and your customers. Includes the NEW WiMAX 802.16e Advantage white paper. Discover how the 16e standard protects and prepares you for future technology evolution vs. 802.16d-based systems. Click here